The AQUAFORCE e-HV pump stations are pre-engineered and fabricated packaged booster systems designed to transfer and increase the pressure of clean water. The e-HV booster station features our e-SV vertical multistage pumps in two to four pump arrangements to deliver up to 780 GPM and 600 feet. Each pump is outfitted with Xylem’s industry leading Hydrovar® variable speed pump control/VFD with individual pump disconnects to ensure that each pump can be serviced without the need to shut down the entire station.
Each station is fully tested for flow and pressure and comes programmed ready to install.
The AQUAFORCE e-HV provides pressure boosting for a variety of industries and applications including:
Request a quote by completing the following form or call 336-665-0250, so we can help you with the best solution for your application. We’re at your service.
AquaBoost Advanced Packaged Systems are simple to specify, simple to install and simple to set up. Best of all, with Xylem’s single-source responsibility and technical expertise, it’s simple to work with us. The AquaBoost Advanced Packaged Systems are a pre-engineered, factory assembled line of packaged booster systems that provide hydraulic capabilities from 20 GPM to 220 GPM and boosts up to 55 psig. AquaBoost Advanced Packaged Systems feature the Aquavar® IPC Variable Speed Controller to give you an intelligent pump system that provides maximum value, proven reliability, superior energy efficiency and better system protection. In addition, it provides consistent performance even with your changing system demands. The AquaBoost Advanced Packaged Systems are built with the quality you’ve come to expect from Goulds Water Technology and provide pressure boosting for a variety of industries and applications including:
Industrial and General Manufacturing
Commercial Building Services
Condominiums and Apartments
Hospitals
Schools
Hotels, Inns and Resorts
Sports Facilities
Main Water Systems
Rural Water
Data Centers
HVAC
Irrigation
Rural Boosting Stations
Features:
Pre-engineered, factory assembled packaged booster system
Fabricated with 316L stainless steel NPE centrifugal pumps
Features the Aquavar IPC Variable Speed Controller
Easier start-up and programming with Start-Up Genie
Hand on, Off, and Auto-On buttons available for easy pump operation at the keypad Pump run-out protection
No toggling between local and remote operation
System redundancy with multi-master control in case of drive failure
Built in system protections (pump run out, dry run, overvoltage, undervoltage, blocked suction, cavitation, NPSHa, phase loss, short circuit, transducer failure and motor current overload)
Programmable lead/lag alternation (duplex) and system pressure
Request a quote by completing the following form or call 336-665-0250, so we can help you with the best solution for your application. We’re at your service.
This beautiful booster package assembled last week in Greensboro Fabrication and is a great example of cross team collaboration. This booster system features Goulds Water Technology e-SV, ITT PumpSmart, ESSCO enclosures and wiring with Tencarva Fabrication welding and assembling the piping and components.
The Triplex e-SV (vertical multistage high pressure pump) system is comprised of 3 e-SV multistage pumps mounted on a Tencarva fabricated common base.
The pumps are Goulds Water Technology 66SV with 75HP motors operating in multi-pump mode and are controlled by three version 6, ITT PumpSmart drives. The cabinet, drives, fusing, switching, wiring and controls were assembled and configured by ESSCO.
In addition to the pipe, welding and fabrication, the mechanical design work and AutoCAD submittal drawing that helped win the order were done by the Tencarva Fabrication Department in Greensboro.
The Aquavar e-ABII pump controller provides an economical answer for municipal and private water systems with low water pressure. Both domestic and light commercial above ground boosters can benefit.
As water use increases, the controller changes pump speed to maintain pressure. Large supply tanks are eliminated and up to 50% of the energy required by a full speed pump is saved.
Increasing competition for water resources has made water conservation a priority. Measuring the flow rate of water is the first step to good water management and can also be very important when installing lawn sprinklers.
The easiest way to measure flow rate is with a flow rate meter. However, if one is not available, there are ways to measure the cubic feet per second (cfs) flowing through your pipes by using formulas or tanks and stopwatches.
Contains information related to marketing campaigns of the user. These are shared with Google AdWords / Google Ads when the Google Ads and Google Analytics accounts are linked together.
90 days
__utma
ID used to identify users and sessions
2 years after last activity
__utmt
Used to monitor number of Google Analytics server requests
10 minutes
__utmb
Used to distinguish new sessions and visits. This cookie is set when the GA.js javascript library is loaded and there is no existing __utmb cookie. The cookie is updated every time data is sent to the Google Analytics server.
30 minutes after last activity
__utmc
Used only with old Urchin versions of Google Analytics and not with GA.js. Was used to distinguish between new sessions and visits at the end of a session.
End of session (browser)
__utmz
Contains information about the traffic source or campaign that directed user to the website. The cookie is set when the GA.js javascript is loaded and updated when data is sent to the Google Anaytics server
6 months after last activity
__utmv
Contains custom information set by the web developer via the _setCustomVar method in Google Analytics. This cookie is updated every time new data is sent to the Google Analytics server.
2 years after last activity
__utmx
Used to determine whether a user is included in an A / B or Multivariate test.
18 months
_ga
ID used to identify users
2 years
_gali
Used by Google Analytics to determine which links on a page are being clicked
30 seconds
_ga_
ID used to identify users
2 years
_gid
ID used to identify users for 24 hours after last activity
24 hours
_gat
Used to monitor number of Google Analytics server requests when using Google Tag Manager
Commercial Building Services
